Dust-Hog SUPRA-CONIC Troubleshooting Guide

Supra-BlastCartridge Dust CollectorInstallation and Operation Manual

6United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02Figure 3. Supra-Blast SBD Typical Installation Diagram44-10003-0001, REV

7United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02Figure 4. Recommended Unit Clearances44-10007-0001

8United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02In the case of spark producing processes, systemdesign should incorporate

9United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02Figure 5. Leg Assembly DetailsFIELD_INSTALL_DWG1/SUPRABLAST/SALES/FIELD_I

10United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02Figure 6. Leg Brace Assembly DetailsFIELD_INSTALL_DWG1/SUPRABLAST/SALES/

11United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02NOTE: Each hopper assembly is equipped with four 1/2"(13 mm) pry lo

12United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02with the hardware provided. Secure leg assemblies tothe concrete mountin

13United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02Figure 7. Hopper Assembly DetailsFIELD_INSTALL_DWG1/SUPRABLAST/SALES/FIE

14United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02Figure 8. Module to Hopper Assembly DetailsFIELD_INSTALL_DWG1/SUPRABLAST

15United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02Figure 9. Multiple Filter Module Section Assembly DetailsFIELD_INSTALL_D

16United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02Figure 10. Top-Mount Blower Support Leg Assembly44-10064-0001

17United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02Figure 11. Power and Elementary Wiring for Units with Supra-Clean Timerb

18United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02Figure 12. Power and Elementary Wiring for Units with Supra-View Panel44

19United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02Figure 13. Power and Elementary Wiring for Units with Supra-I.Q. Diagnos

20United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02Figure 14. Solenoid Wiring to Pulse Controls61-10004-000104-2554, REV C

multiple module solenoid valve enclosures with heatersare installed, daisy chain the wiring so that each heaterwill have 100/115/VAC, 50/60 Hz at all

Figure 15. Pneumatic Valve Assembly44-10042-000122United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02

Figure 16. Abrasive Inlet Installation44-10045-000123United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02

ROTARY AIR LOCK INSTALLATIONIf a rotary air lock was ordered with the unit, the hopperdischarge will have an adapter already bolted to it. Makecertain

If a drum lid latch kit was ordered, attach the separateclamp band around the 55-gallon (208 liter) drum or30-gallon (114 liter) short drum, leaving t

TABLE OF CONTENTSPage1. IMPORTANT NOTICE ... 11.1 General Caution

Figure 18. Supra-Blast Typical Pressure Gauge Installation44-10043-0001, REV A26United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised

supply interconnecting signal cord and mountinghardware for remote blower start/stop assemblyinstallation. Remove jumper between terminals L and 20in

Check the differential pressure reading across thedust collector clean to dirty air sections. A normaldifferential pressure drop reading is between 1&

PHOTOHELIC GUAGE CONTROL WITHSUPRA-CLEAN TIMERBOARDWhen using a Photohelic Guage with Supra-Cleantimerboard, the timerboard is set to “PS” pulse mode(

Figure 19. QuickSeal Filter Access Door and Supra-Max Series Filter Installation44-10006-000130United Air Specialists, Inc.Supra-BlastCartridge Dust C

TO REPLACE CARTRIDGE FILTERS(refer to Figure 19):1. Read and follow caution instructions in Section 6before servicing dust collector. Start with the t

gate, close the slide gate before servicing the duststorage drum(s). The dust collector fan and compressedair cleaning systems do not have to be turne

!CAUTIONAll electrical wiring troubleshooting should beperformed by a qualified electrician in accordancewith local electrical codes.!CAUTIONPrior to

Continual, excessive pressure Compressed air supply problems. Check incoming compressed air for proper supply atdrop (over 7" [178 mm]) on filter

8. ILLUSTRATED PARTSDUST-HOG® Supra-Blast Series44-10009-000135United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02

Supra-Blast Series Dust Collector Bill of MaterialsItem Part No. Description1 33-10001-XXXX Supra-Max Series Cartridge Filter (refer to Section 6.7 fo

UNITED AIR SPECIALISTS, INC.LIMITED WARRANTYUAS warrants all equipment manufactured and sold by UAS against defective parts and workmanship for oneyea

To Order Genuine Supra-Blast Replacement Partsand Supra-Max Series Replacement Filters,Contact the Nearest United Air Specialists Office.United Air Sp

1United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/021. IMPORTANT NOTICEThis manual contains important safety information andp

2United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02EXAMPLE: SBD 24-3-H55SBD – DUST-HOG Supra-Blast double-filterconfiguratio

3United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02Figure 1. Supra-Blast Air Filter Operation & Cleaning44-10001-0001

4United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/023. SPECIFICATION TABLE4. INSTALLATION4.1 OFF LOADING AND INSPECTIONSupra-

5United Air Specialists, Inc.Supra-BlastCartridge Dust CollectorRevised 02/02Figure 2. Supra-Blast SBS Typical Installation Diagram44-10044-0001, REV